It appears that your cart is currently empty
Monday -Friday 8am-5pm PST Phone # (541)497-2882
3 Inch 7.3L Billet Intake Plenums
Description
THESE INTAKE PLENUMS ARE FOR 10 BOLT 7.3 HEADS
These billet intake plenums are a nice upgrade over the stock flimsy stamped sheet metal and will not deform the center inlet port when installing your CAC boot clamps.
Features:
- High strength 6061-T6511 aircraft aluminum
- Bolt/nut kit included
- Tube of Permatex Ultra Gray RTV sealant included
- Will work with all aftermarket HPOP line kit fittings
- CNC machined in-house
- Will work with all aftermarket fuel line kits
- Thicker wall for higher boost applications
- Made in the USA
**If you are swiitching over to a T4 turbo mount for an 94.5-97 (OBS) or Early '99 setup these 3" plenums are what you want to use.**
INSTALLATION:
After removal of the old plenums, make sure the surface of the head and new plenum is absolutely clean of any dirt, debris, previous RTV sealant or the new plenums may not seal properly. Apply a small bead of sealant around the outside flange following the groove and go around each bolt hole. Do not apply too much sealant to avoid large globs getting into the intake runners of the cylinder head after the sealant has cured. Follow the instructions on the back of the tube of sealant. After you have placed the sealant on a plenum, install it on the head slowing by watching the bolt holes to line them up as best you can. Install each bolt finger tight. If you are using the original mount for the GPR there are nuts included to better match the bolts in the kit. After each bolt has been installed finger tight, start in the center of the plenum and work towards the ends tightening the bolts with a wrench. 3/8" ratchet with a 13mm shallow socket and 4" extension works great for all bolts except the one on the passenger side at the front of the engine (you'll need at 13mm combination wrench) that cannot be removed unless you either pull the front cover or have the head off the engine. **You will not be able to install one of the provided bolts in this location unless the front cover is off or you have the head off, the factory bolt can be reused without issue. This one bolt must be installed prior to engine assembly. Bolts are to be torqued to 20ft/lbs.
If you are unsure of installing yourself, seek out a competent and qualified technician to install this kit.
Your may also be interested in following product
KC300x Stage 2 Turbo (63/73) - 7.3 Powerstroke ...
KC300x Stage 2 OBS Gen 2 Supports: Up to 205cc/30% injectors Features & Details: Powder Co...
KC300x Stage 2 OBS Gen 2 Supports: Up to 205cc/30% injectors Features & Details: Powder Coating can take up to 3 weeks before it ships 100% drop in turbo (no modifications required) 63mm 7x7 SXE style compressor wheel with extended tip technology 73mm SXE style turbine wheel 4" ported compressor housing with drilled anti-surge for high flow High Flow Non-EBPV outlet flange Upgraded 360 Thrust Journal Bearing Design Comes with all gaskets and o-rings to install Comes with new 4" intake...
€1.207,66 – €1.451,14
Insight CTS3 - Touchscreen Monitor
(NOTE)-THE CTS3 WILL ONLY MONITOR VOLTAGE, COOLANT TEMP, OIL PRESSURE, RPM, AND BOOST UNDER 25 PS...
(NOTE)-THE CTS3 WILL ONLY MONITOR VOLTAGE, COOLANT TEMP, OIL PRESSURE, RPM, AND BOOST UNDER 25 PSI THROUGH THE OBII PORT. IF YOU WANT TO MONITOR EGT, BOOST, TRANS TEMP, AND OR FUEL PRESSURE, PLEASE SELECT (YES) FROM THE DROP DOWNS. The Insight is the #1 preferred digital gauge monitor in the market today, used by daily drivers and enthusiasts everywhere. The Insight is the most comprehensive, state-of-the-art, multi-gauge touch-screen display on the market. It is an instantaneous and inexpen...
€384,60 – €1.326,28
(1994-1997) - Diamond Eye 4" Muffler Kit
K4306A – FOR 1994.5 – 1997 – FORD 7.3L POWERSTROKE DIESEL F250/F350 (ALL CAB AND BED LENGTHS) – 4...
K4306A – FOR 1994.5 – 1997 – FORD 7.3L POWERSTROKE DIESEL F250/F350 (ALL CAB AND BED LENGTHS) – 4″ ALUMINIZIED – PERFORMANCE DIESEL EXHAUST KIT – TURBO BACK SINGLE – 3″ (2 PIECE) DOWN PIPE – SYSTEM RE-INCORPORATES FACTORY CATALYTIC CONVERTER.INSTUCTIONS
€486,95
S & B Cold Air Intake for 1988-1995 Ford F-150,...
Currently 2 week back order. DOES NOT FIT VEHICLES WITH MAF SENSORS PLEASE EMAIL OR CALL FOR SHIP...
Currently 2 week back order. DOES NOT FIT VEHICLES WITH MAF SENSORS PLEASE EMAIL OR CALL FOR SHIPPING TO HAWAII, ALASKA OR CANANDA. Filter type Cotton Cleanable Carb exempt id D-590-2 Oil color Red Quantity of oil 53 grams Street legal in all us states Yes Vehicle Fitment 1988-1995 Ford Bronco 5.0L, Gas 1988-1995 Ford Bronco 5.8L, Gas 1988-1995 Ford F-150 4.9L, Gas 1988-1995 Ford F-150 5.0L, Gas 1988-1995 Ford F-150 5.8L, Gas 1988-1995 Ford F-250 7.5L, Gas 1988-...
€183,90
995